DSP Color CCD Cameras
CV-S3200/3300
Oper at ion Manual
(Rev.B)
CV-S3200/ 3300
Table of Contents
CE declaration...........................................................................................................
1. General..................................................................................................................
2. Main features ........................................................................................................
3. Standard composition...........................................................................................
4. Pin assignment .....................................................................................................
2
4
4
5
5
5. Functions and operations .....................................................................................
5.1 SW1 switch on PK8167 board ......................................................................
5.2 On-screen-menu ........................................................................................
5.3 RS 232C functions ......................................................................................
6
6
7
11
6. External appearance .............................................................................................
7. Specifications .......................................................................................................
12
13
8. Appendix ..............................................................................................................
8.1 Precautions ................................................................................................
8.2 Typical CCD Characteristics ........................................................................
8.3 References .................................................................................................
14
14
14
14
9. Users Record .........................................................................................................
15
3
CV-S3200/ 3300
1. General
The CV-S3200/ 3300 is a new high-resolution color camera series, available in PAL or NTSC
format. The camera series was developed with JAI's new DSP processor, which has remarkable
high signal to noise ratio as well as a high bit flow. The cameras also have built-in RAM, which
together with the DSP enables the camera to produce field integration with 100% horizontal
resolution.
The CV-S3200/ 3300 series features EXview HADTM sensors (CV-S3200:1/ 2" and CV-S3300:
1/ 3")which are extra light sensitive and have enhanced anti-smear and blooming characteristics.
The cameras run on 12V DC and can be gen-locked or use VBS for external synchronization.
There are connections for video control or direct drive lens, and VBS and Y/ C video outputs.
Both cameras have CS/ C-mount with a variable mounting ring for back focus. The CV-S3300
has screw terminals for power, gen-lock and line-lock. The CV-S3200 comes with D-sub
connector.
The camera set-up can be performed via the JAI software platform and an RS232C port, or from
a new on-screen menu that can be controlled by the three buttons mounted on the rear of the
camera. Both the software and the on-screen-menu can control the following setting:shutter,
integration, gamma, AGC,H/ V enhancer, iris-level for direct drive, positive/ negative picture,
back-light compensation, and AWB fixed or manual color temperature.
Applications include surveillance, security, medical and a large variety of other industrial
applications.
2. Main Features
1/ 2" EXview HADTM IT color CCD sensor for CV-S3200,
1/ 3" EXview HADTM IT color CCD sensor for CV-S3300
NTSC : 768 (h) x 494 (v) , PAL : 752 (h) x 582 (v)
450 TV lines horizontal resolution
Composite VBS and Y/ C output
Excellent color reproduction
Field integration mode for higher sensitivity
S/ N ratio > 50 dB
White balance automatic or manual
Auto iris and CCD iris for light regulation
Manual shutter up to 1/ 10,000 sec.
Scanning reversal function (mirror-effect mode)
CS-lens mount with focus adjustment
CV-S3200 employs 9 pin Dsub connector at camera rear panel for single cable solution.
CV-S3300 provides 7 pin terminal at camera rear panel for easy cable installation.
4
CV-S3200/ 3300
3. Standard compositions
1) Camera main body
x 1
x 1
x 1
x 1
x 1
2) C-mount adaptor (MP-55)
3) Auto iris lens pulg (E4-191J-100)
4) Y/ C out plug (TCP8040-01-520)
5) Operation manual
4. Pin assignment
4-1. DC IN/ SYNC/ RS-232C connector
a) 9 pin D-sub connector for CV-S3200
1 : Ground
2 : +12V DC input
3 : Ground
4 : VBS output
5 : Sync input
6 : Y output
4-40
UNC Thread
7 : C output
8 : TXD output
9 : RXD input
b) 7 pin terminal for CV-S3300
1 : RXD input
2 : TXD output
3 : Ground
4 : Sync. input
5 : Ground
6 : +12V DC input
7 : Ground
5
CV-S3200/ 3300
4-2. S-VIDEO connector
1 : Ground
2 : Ground
3 : Y output
4 : C output
4-3. LENS connector
1 : +9V / Damp-
2 : NC / Damp+
3 : Iris / Drive+
4 : Ground / Drive-
5. Functions and operations
5-1. SW1 switch on PK8167 board
This switch is to select the type of auto iris. It is located on the CCD board (PK8167), as below.
Up
: Direct drive mode (Passive)
Down : Video controlled (Active)
SW1 switch
Note : Factory pre-set is Video controlled.
6
CV-S3200/ 3300
5-2. On-screen-menu
On-screen-menu can be controlled by the “UP”, “DOWN” and “FUNC” switches on the rear panel.
5-2-1. Functions
The following functions are adjustable at on-screen-menu.
White balance
Shutter
Gain
Back light compensation
Lens iris
Gamma
Scanning reversal
Sensitive (Field integration)
a) White balance
This function is to adjust the color temperature to make the color of the image correct.
3200 K
4600 K
5600 K
Auto
: For incandescent lamp or halogen lamp.
: For white fluorescent lamp.
: For daylight.
: The TTL system is employed for auto white balance, and it detects the
highest video level in objects to recognize a white color.
It is necessary to place the camera in a position where the camera does
not pick up spot lights and fluorescentlights.
Manual
: To adjust the color temperature between 2700 K to 6700 K.
: Refer to 5-2-2 (d).
One push
Note : Factory pre-set is auto white balance.
7
CV-S3200/ 3300
b) Shutter
This function is used for “freezing” objects and for light regulations. Nine exposure time settings are
available.
OFF
: 1/ 60 sec. (NTSC), 1/ 50 sec. (PAL)
Selectable shutter: 1/ 125, 1/ 250, 1/ 500, 1/ 1000, 1/ 2000, 1/ 4000, 1/ 10,000 sec.
Flicker-less
CCD iris
: 1/ 100 sec. (NTSC), 1/ 120 sec. (PAL)
: Shutter speed changes automatically.
(1/ 60 sec. to 1/ 10000 sec. (NTSC), 1/ 50 sec. to 1/ 10,000 sec.(PAL))
Note : Factory pre-set is OFF.
CAUTION
Under certain unique light conditions, the following may appear.
- Strong smear and/ or blooming on highlighted objects.
- Noticeable flicker in the picture.
1.
CCD iris
2.
3.
Continuous variable electronic shutter controls the exposure time of the CCD sensor, depending on the incoming
light level. When this mode is selected, auto or manual iris lens can be used instead of an auto iris lens.
Shutter speed and sensitive mode
In sensitive made the CCD iris does not function.
c) AGC (Auto gain control)
OFF
:
:
Gain is fixed at minimum 0 dB
AGC ON (0 to +12 dB)
+12 dB
+24 dB : AGC ON (0 to +24 dB)
Manual : Manual gain
Note : Factory pre-set is AGC OFF.
CAUTION
1. Auto iris lens can be used only when the CCD iris is OFF.
8
CV-S3200/ 3300
d) BLC (Back Light Compensation)
BLC circuit will c0mpensate for extreme highlights in the field of view.
There are three pre-defined patterns that can be selected. These are shown below. The higher
the value, the more backlight compensation.
Patten 3
Patten 2
Patten 1
1
1
1
1
0
0
0
0
0
0
4
4
9
4
0
15
0
0
10
0
4
Note : Factory pre-set is OFF.
CAUTION
The BLC works under the follwing conditions:
1.
BLC
: Effective
: Not-effective
AGC
ON
ON
ON
OFF
ON
OFF
OFF
CCD iris
OFF
It is recommended to switch “BLC OFF” when using the camera with pan/ tilt head or if the scene illumination
changes rapidly.
2.
3.
With “BLC ON” the regulation speed of the iris is decreased.
e) Iris level
This is to set the video level, when the camera is set at CCD iris, AGC ON and auto iris.
9
CV-S3200/ 3300
f) Gamma
This function is to set the gamma correction.
0.45
0.6
: Correction
: Correction
: Linear
1.0
Note : Factory pre-set is 0.45.
g) Scanning reversal (mirror-effect mode)
This function can change the horizontal scanning between normal and reverse.
OFF
ON
: Normal scanning
: Reversal scanning
Note : Factory pre-set is set at OFF.
h) Field integration
The sensitivity can be set at these pre-set positions.
:
:
:
:
:
:
:
OFF
2F
Standard sensitivity (Exposure time = 1 field)
2 times higher than standard sensitivity (Exposure time = 2 fields)
4 times higher than standard sensitivity (Exposure time = 4 fields)
8 times higher than standard sensitivity (Exposure time = 8 fields)
16 times higher than standard sensitivity (Exposure time = 16 fields)
32 times higher than standard sensitivity (Exposure time = 32 fields)
64 times higher than standard sensitivity (Exposure time =64 fields)
4F
8F
16F
32F
64F
Note : Factory pre-set is OFF.
5-2-2. Operations
Screen display (example)
Function buttons for on-screen-menu
White balance
Manual
Rear panel of CV-S3300 (example)
Red
Blue
Note : This scroll bar will be displayed when the following
functions are selected.
White balance = manual, AGC = manual, Iris = manual
10
CV-S3200/ 3300
(a)
(b)
(c)
(d)
To start adjustment, push the “FUNC” button. The menu will appear on the monitor .
(See page 12)
Use “UP” or “DOWN” buttons to choose functions. To select function, press the “FUNC”
button.
After selecting the function, press “UP” or “DOWN” buttons to choose mode. To select
mode, press the “FUNC” button.
To use One Push White Balance.
Go to the next function if needed, and repeat (b) to (c).
1. Change to White Balance mode by Function SW.
2. Change to One-push mode by Up or Down SW.
3. Push Function SW and make it READY.
4. Push Up SW, and One-Push White Balance function starts.
5. Push Function SW to save the data (R.B.Gain) of One-Push White Balance.
If you turn off the power without saving the data, it will return to the original status.
5-3. RS 232C functions
: To adjust the color temperature
: To adjust the shutter speed
a) White balance
b) Electronic shutter
c) Auto gain control
d) Back light compensation
e) Iris level
: OFF, +12dB, +24dB, manual selectable
: To create your own BLC pattern.
:
To adjust the video level
: 0.45, 0.60, 1.0 selectable
: To select the scanning direction
: To select the sensivity
f) Gamma
g) Scanning reversal
h) Frame integration
11
CV-S3200/ 3300
6. External appearance
Unit : mm (inches)
e.g. CV-S3200
e.g. CV-S3300
12
CV-S3200/ 3300
7. Specifications
µ
µ
µ
µ
>
Note : Above specifications are subject to change without notice.
13
CV-S3200/ 3300
8. Appendix
8-1 Precautions
Personnel not trained in dealing with similar electronic devices should not service this camera.
The camera contains components sensitive to electrostatic discharge. The handling of these devices
should follow the requirements of electrostatic sensitive components.
Do not attempt to disassemble this camera.
Do not expose this camera to rain or moisture.
Do not face this camera towards the sun, extreme bright light or light reflecting objects.
When this camera is not in use, put the supplied lens cap on the lens mount.
Handle this camera with the maximum care.
Operate this camera only from the type of power source indicated on the camera.
Power off the camera during any modification such as changes of jumper and switch setting.
8.2 Typical CCD Characteristics
The following effects may be observed on the video monitor screen. They do not indicate any fault of the
CCD camera, but do associate with typical CCD characteristics.
V. Smear
Due to an excessive bright object such as electric lighting, sun or strong reflection, vertical smear may be
visible on the video monitor screen. This phenomenon is related to the characteristics of the Interline
Transfer System employed in the CCD.
V. Aliasing
When the CCD camera captures stripes, straight lines or similar sharp patterns, jagged image on the
monitor may appear.
Blemishes
Some pixel defects can occur, but this does not have en effect on the practical operation.
Patterned Noise
When the CCD camera captures a dark object at high temperature or is used for long time integration,
fixed pattern noise (shown as white dots) may appear on the video monitor screen.
8.3 References
14
CV-S3200/ 3300
9. User’s Record
Camera type:
CV-S3200/ 3300
(Revision B)
.................
Revision:
Serial No.
Users Mode Settings
Users Modifications
15
JAI Corporation, Japan
German Industry Center
1-18-2 Hakusan, Midori-ku
Yokohama,
Kanagawa 226-0006, Japan
Phone +81 45 933 5400
Fax +81 45 931 6142
JAI America, Inc., USA
Suite 450
23046 Avenida de la Carlota
Laguna Hills, CA 92653
USA
Phone +1 949 472 5900
Fax +1 949 472 5908
JAI A·S, Denmark
Produktionsvej 1, 2600 Glostrup
Copenhagen, Denmark
Phone +45 4457 8888
Fax +45 4491 8880
|